Pimp my Canooo, Take twooo

 Hi crew, Most of you would have seen my canoe modifacations on a previous post (  fishwrecked.com/forum/new-micro-dinghy  ) 

But i found a few problems over time using the canoe. To start with the seat i put in was unstable and almost put me in the drink a few times. It was also heavy and to move the boat around it would fall over and realy anoyed me . So i decided to suport the sides and create a new seat bracket.

I started with some aluminium tube, and by hand formed the curves i wanted to fit under the sides of the canoe.

I checked the tube on the sides to make sure i got them right.

Then i worked on the seat mount, deciding to just go with a standard plastic seat to keep to weight down.

The frame with the seat fitted, and agian checking that it will fit properly before putting it in.

It took a bit of work to get it in place but the frame went under the sides and was bolted in with stainless steel fittings. 

I think it went very well with the seat sitting just above the floor, and the side lost all the flex that had bothered me so much. The total weight of the aluminum and seat was almost the same as the seat and bracket i removed.

Next problem was the bottom. I have been draging it across carparks and gravel that was wearing out the plastic. So i got a couple trailer skids and using a very good quality glue, fitted them to the bottom .

I also used some stainless steel rivets to make sure they would not fail on me and come loose . They work realy well, and fully loaded with all my gear , the canoe glides over everything straight to the back of my Patrol, then loads inside with the seats folded down.

One problem i have had on the river, is other boats nearly running me over on dusk. One of my mates pointed out " well you did paint it camo " 

So the only way to sort this out was add some Nav lights, and if i'm going to carry a battery I may as well have a sounder. I Picked up a new one with downvision options for $220.

I got a small 7a/h battery and made an aluminium box to hold it, plus mount the sounder.

 I made it fit the small pocket at the front of the canoe so it is portable and can be taken out easily.

I put fuses in line, with two switches for the sounder and the nav lights. I can also charge the battery without opening the box. I made a mount for the transducer that clips on, so if i hit any logs it will not get damaged and can easily remove it for storage.

The rig all set up ready to go.

Ive been out a few time this week and all is good so far. The seat is a lot better and stable, the sounder works great and no one has run me over yet with the lights on after dark. Been getting heaps of Bream and sneaking around all the private jetty's without anyone bothering me, but thats another story to tell later. ( Report coming soon ) 

Cheers Grant ..

 

Image Upload: 

scano's picture

Posts: 1246

Date Joined: 31/05/07

Very impressed

Fri, 2014-03-28 03:22

 Some awesome fabrication work!!

 

you have obviously been doing metalwork for many years.

i hope you get plenty of good hours hunting fish out in this bad boy. It looks awesome!!

____________________________________________________________________________

 

 

scotto's picture

Posts: 2469

Date Joined: 21/04/08

Neat as

Fri, 2014-03-28 05:57

 Tidy work grant

big john's picture

Posts: 8725

Date Joined: 20/07/06

Talent

Fri, 2014-03-28 06:39

 Great job Grant, if you're not already doing it, you should be advertising boat and canoe modifications.

____________________________________________________________________________

WA based manufacturer and supplier of premium leadhead jigs, fligs, bucktail jigs, 'bulletproof' soft plastic jig heads and XOS bullet jig heads.

Jigs available online in my web store!

sea-kem's picture

Posts: 14833

Date Joined: 30/11/09

 Bloody awesome Grant!

Fri, 2014-03-28 06:50

 Bloody awesome Grant!

____________________________________________________________________________

Love the West!

opsrey's picture

Posts: 1200

Date Joined: 05/10/07

Skid glue.

Fri, 2014-03-28 07:06

 What was the glue you used on the slids. Kayak looks the goods, hope you get a few fish from it. 

grantarctic1's picture

Posts: 2546

Date Joined: 03/03/11

The Glue

Fri, 2014-03-28 10:51

The Glue was Sikaflex- 252. Its a construction adhesive that retains flexability after it sets. I roughly sanded both surfaces to give grip to the glue, then apllied it to both surfaces and riveted it in place. Then i went around the edges to fill any gaps, i let it cure for 3 days to make sure it set properly.

 

crasny1's picture

Posts: 6985

Date Joined: 16/10/08

Awesome mate

Fri, 2014-03-28 10:15

now we just need some action shots!!!!

Edit: And PS

Soon with the mods you doing to that thing it with morph into a 23ft CC glass boat

____________________________________________________________________________

"I would like to die on Mars. Just not on impact!!" _ Elon Musk